Primera PX450 Manual de usuario

User's Manual© 2009 All rights reserved060209-511250-(02)(Color Printer 450)511250.qxd 6/2/2009 6:43 PM Page i

6 Hardware and Software Settings4. Select "Install the software automatically" and click Next.You may see a notice like the one shown here s

Hardware and Software Settings 7C. INSTALLING MEDIAYour printer will utilize awide variety of continuousmedia. Most inkjet receptivemedia within the p

8 Hardware and Software Settings4. Place the media roll between the Roll Core Holders andrelease the spring-loaded Media Guide to hold the roll.The R

Hardware and Software Settings 9For narrow media it may be necessary to adjust the media sensor position. The scale on the Media Sensor Bar represent

10 Hardware and Software SettingsD. INSTALLING THE INK CARTRIDGEYour printer has a built-in ink tracking system. This system isdesigned to warn you i

Hardware and Software Settings 11E. ALIGNING THE INK CARTRIDGECartridge alignment is optional and is only necessary if youwould like to improve print

12 Using the Integrated CutterSection 3: Using the Integrated CutterThe printer has an integrated cutter that is designed to cutmedia on a continuous

Using the Integrated Cutter 13Offsets - Cut Position:With this setting you can fine-tune the cut position after theimage prints. Increase this value t

14 Printer SettingsSection 4: Printer SettingsA. PC PRINTER DRIVER SETTINGSRefer to the following steps to change or verify your defaultprinter driver

Printer Settings 15Paper SizeThis setting allows you to set the height and width of yourprint image in .01" or .1mm increments.OrientationThere a

iiNotices: The information in this document is subject to change without notice. NO WARRANTY OFANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDIN

16 Printer SettingsBest for Photos mode is best used for photographic imageswhere accurate color reproduction is essential. Images printedin this mod

Printer Settings 17This number can also be used to calculate total number ofprints you can get from one cartridge and also ink cost perlabel. Use the

18 Printer SettingsDetails/Print CounterClicking on the Details button will allow you to view information about printer settings stored in the printer

Printer Settings 19Output ModeDo not present. The media does not move after the last imageis printed. This means that part of the last image printed

20 Printer SettingsLeft Margin OffsetThis will be factory calibrated. If fine-tuning is needed,increase this setting to move the image right on the me

Advanced Configuration Settings 21Section 5. Advanced ConfigurationSettingsWhen the printer driver is installed in Section 2, a configurationINI file

22 Advanced Configuration Settings; 0 = DBGLVL_ZERO; 1 = DBGLVL_TRACE ; 2 = DBGLVL_DUMP; 3 = DBGLVL_INFORM (default if not specified); 4 = DBGLVL_WARN

Advanced Configuration Settings 23; 0 = disable horizontal scan; 1 = enable scan at the end of each print (fast but may not be as accurate - if printi

24 Advanced Configuration Settings;; 1 = Reflective Mode (e.g. Black mark on back);; 2 = Continous Stock (don't use sensor);; 255 = Use printer s

Troubleshooting 25Section 6: Troubleshooting A. SOLVING REGISTRATION PROBLEMSImage is Vertically OffsetWhen printing on media other than continuous, t

iiiTable of ContentsSection 1: Getting Started...1A. Choosing a Good Locat

26 Troubleshooting2. Nonstandard / Non-translucent Backing Material. If youhave purchased label stock from someone other thanPrimera, test the unit w

Troubleshooting 27Note: Often times a space on the right (printer’s left) side indicates a margin around the media that is not being accounted for. Th

28 TroubleshootingB. CLEARING A MEDIA JAMIf there is a media jam in the printer mechanism, first attemptto remove the jam by opening the Top Cover and

Troubleshooting 29D. CLEANING THE INK CARTRIDGEIt may be necessary to clean the ink cartridge nozzles if younotice reduced print quality, or if you su

30 Media and Roll SpecificationsSection 7: Media and Roll SpecificationsImportant Note: Printing labels is not recommended as this printer was design

Media and Roll Specifications 31Label Side Out Core I.D. Core O.D. Roll O.D. Notes: 1. Label height <1.5” requires a 2.00” I.D. x 3.00” O.D. core.

32 Technical SpecificationsSection 8: Technical SpecificationsPrint Method: InkjetPrint Resolutions: 4800 x 1200 dpi, 1200 x 1200 dpi, 600 x 600 dpi

Index 33IndexCartridge Alignment ...11, 16Cleaning the Ink Cartridge...

Printed in the United States of AmericaP/N 511250511250.qxd 6/2/2009 6:44 PM Page 36

There are interactive features that will allow you to jump to different locations within the document. Each listing inthe Table of Contents is interac

Getting Started 1Section 1: Getting StartedTHANK YOU…...for choosing an PX450 Color Point-of-Sale Printer. The PX450Printer will print full color po

2 Getting StartedB. UNPACKING AND INSPECTIONWhile unpacking your printer, inspect the carton to ensure that no damage has occurred during shipping. M

C. IDENTIFYING THE PARTSThis illustration shows the front of the printer with its controlbuttons and LED indicator lights.The Power LED indicates that

4 Getting StartedThis illustration shows the input ports and power switch foundon the rear panel of the printer. D. COMPUTER SPECIFICATIONSMinimum PC

Hardware and Software Settings 5Section 2: Hardware and SoftwareSetupA. CONNECTING POWER1. Locate the Power Adapter supplied with your printer.2. P