Primera Digital label and decal press 3 Manual de usuario

© 2012 All rights reservedFor the most recent version of this manual please visithttp://www.primera.com/manuals.html062812-511311USER’S MANUALMedicalS

6 Getting StartedE. CONNECT POWERAttach the power cord to the Power brick. Plug the power cord into a grounded outlet and the 5mm barrel connector tot

Getting Started 7F. LOAD A RIBBONThe Signature Slide Printer uses either a Black ribbon (5000prints) or a CMYK Color ribbons (1000 prints). You must

8 Getting Started3. Remove the ribbon from its shrink wrapped packaging.Hold the take up (back) ribbon core with your left hand.Hold the supply (front

Getting Started 95. Rotate the hubs until the tabs on the right side hubs matchthe notches on the ribbon. Manually turn the take up coreuntil the ri

10 Getting StartedG. LOAD A SLIDE CARTRIDGE1. Remove the empty blue slide cartridge by pulling up and out.2. Open the blue side cartridge. 3. Locate t

Getting Started 114. Place the slides next to the blue side cartridge so that the printable surface is on the TOP of the slide with the orientation s

12 Getting Started6. Once the slides are in place, straighten any that did notproperly fall in the cartridge and ensure the printable surface is facin

Getting Started 13H. INSTALL THE PRINTER DRIVERIf you have purchased the Primera Touch Screen you will notneed to install the printer driver. It wil

14 Printing SlidesSection 2: Printing SlidesIf you have purchased the Primera PTLAB software or thePrimera Touch Screen Computer with the PTLAB softwa

Printing Slides 15Paper Size: Default paper size is set to the maximum. Editthese settings if you are printing to slides with a smaller print-able ar

iiNotices: The information in this document is subject to change without notice. NO WARRANTY OFANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDIN

16 Maintenance and TroubleshootingSection 3: Maintenance and TroubleshootingA. INDICATOR LIGHTS AND ERROR CODESPower light on Steady - Ready to recei

Slide Cartridge Invalid 80 0Ribbon PWM 40 0Head Load 20 0Input Empty 10 0Input Jam 08 0Ribbon Advance Error 04 0Ribbon Invalid 02 0Lifter Not Function

18 Maintenance and Troubleshooting3. Locate the Print head mounted to the underside of the cover.4. Clean the print head using the print head pen.

Maintenance and Troubleshooting 194. Push back , then down and then flip it 180 degrees toreveal the cable connector. Watch the pin on the side of th

6. Connect the new print head. 7. Rotate the printhead 180 degrees and push it back into themetal housing. 8. IMPORTANT! Find the Resistance value

Maintenance and Troubleshooting 21Vertical Line. A line vertically through theentire print is cause by dust or debris on theprint head burn line or bl

22 Maintenance and TroubleshootingRandom Missing Area (Printable SurfaceMissing). If the printable surface is missing orscratched off, the printer can

Maintenance and Troubleshooting 233. Feed the supply side of the ribbon under the take up roll.Tape the supply ribbon to the take-up roll. 4. Manual

24 Maintenance and Troubleshooting3. Remove the slide cartridge.4. In the slide cartridge compartment check near the bottomroller for a slide.5. Check

Maintenance and Troubleshooting 257. Finally if the slide is broken you can remove it using thebottom catch bin. Pick up the slide printer and rotate

iiiTable of ContentsSection 1: Getting Started...1A. Choosing a Good Locat

26 Maintenance and TroubleshootingH. TECHNICAL SUPPORTIf you have difficulties in operating your Printer, the proce-dures in this manual and the softw

Technical Specifications 27Section 4. Technical SpecificationsPrinting technology: Thermal transferPrint speed: Up to 7 slides/minute (monochrome)Up t

Printed in the United States of AmericaP/N 511311MedicalSlide.qxd 6/28/2012 1:23 PM Page 28

There are interactive features that will allow you to jump to different locations within the document. Each listing inthe Table of Contents is interac

Getting Started 1Section 1: Getting StartedTHANK YOU…...for purchasing a Signature Slide Printer. The Signature SlidePrinter can significantly incre

2 Getting StartedB. UNPACKING AND INSPECTIONWhile unpacking your Printer, inspect the carton to ensure thatno damage has occurred during shipping. Mak

C. INDENTIFYING THE PARTSThe following illustrations show the various parts of the printer. These parts will be referred to throughout this manualso

4 Getting StartedRear ViewRear AccessPanelUSBPowerMedicalSlide.qxd 6/28/2012 1:23 PM Page 4TOC

Getting Started 5D. SLIDE SPECIFICATIONSSlides should be 1.00" x 3.00" x .040" with clipped corners(1mm x 1mm). They should have grou