Primera Disc Autoloader ADL-MAX Manual de usuario Pagina 1

091506-510975-(01)USER’S MANUAL© 2006 All rights reserved.DISC AUTOLOADER510975.qxd 9/28/2006 9:38 AM Page i

8. Once recording has started, the recorded discs from theprevious round will be transported to the Input Bintemporarily, and will then be transported

Hardware and Software Set-Up and Testing 7Section 2: Hardware and Software Set-Up and TestingA. SOFTWARE INSTALLATIONImportant Note: You must instal

8 Hardware and Software Set-Up and TestingB. CONNECTING THE CABLES • Remove the tape securing the arm to the base plate of the Autoloader.• Locate the

Hardware and Software Set-Up and Testing 9You may see a notice like the one shown here stating that the software has not passed Windows Logo Testing.

10 Hardware and Software Set-Up and TestingC. INSTALLING THE DISC PUBLISHER STAND• Lower the Disc Publisher Stand onto the Autoloader sothat the metal

Hardware and Software Set-Up and Testing 11• Attach the stand to the unit using the adjustment bolts andthe washers. Do not tighten the bolts at thi

12 Hardware and Software Set-Up and Testing• Install the cables, ink cartridges etc. according to theinstructions in the Disc Publisher users manual.

Hardware and Software Set-Up and Testing 13F. CALIBRATING THE AUTOLOADER TO THE DISCPUBLISHER• Calibrate the arm to the Disc Publisher by opening the

14 Hardware and Software Set-Up and Testing• After calibrating the Disc Publisher position by moving thestand forward or backward, make sure you tight

Running Your First Job 15Section 3: Running Your First JobA. BURNING AND PRINTING THROUGH PRIMODVDWhen the Disc Publisher is connected to the ADL-MAX

iiNotices: The information in this document is subject to change without notice. NO WARRANTY OFANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDIN

16 Running Your First JobYou may also recalibrate the ADL-MAX by clicking CalibrateADL-MAX button. Several calibration options are available. Last Di

Running Your First Job 173. Select your SureThing label file by clicking the Browsebutton.4. Enter the number of copies.5. Click Print.To recalibrate

18 Running Your First JobC. CHANGING CARTRIDGESDuring normal operation you will be prompted to change thecartridge at the same time the low ink warnin

Maintenance and Troubleshooting 19Section 4: Interpreting the Autoloader'sLED Status LightsThe LED Status Lights are located on the front Contr

20Maintenance and TroubleshootingSection 5: Maintenance andTroubleshootingThe unit is designed to operate for extended periods of timewith very little

Technical Specifications 21Section 6: Technical SpecificationsModel ADL-MAXOptional Duplicators Disc Publisher II, AutoPrinter II, Disc Publisher Pro

22 IndexIndexAutoPrinter ...16Cables ...

Printed in the United States of AmericaP/N 510975 510975.qxd 9/28/2006 9:39 AM Page 24

Table of ContentsSection 1: Getting Started...1A. Choosing a Good Location

There are interactive features that will allow you to jump to different locations within the document. Each listing inthe Table of Contents is interac

Getting Started 1Section 1: Getting StartedTHANK YOU…...for purchasing the ADL-MAX. It is the perfect way for you toadd capacity to your existing Disc

B. UNPACKING AND INSPECTIONMake sure that all supplied accessories are included with yourunit. The following items should be included:• ADL-MAX • Dis

C. IDENTIFYING THE PARTSFront Panel and TopThis illustration shows the Autoloader, its Control Panel,Buttons, LED indicator lights, Input/Output Bins

The Pause Button immediately pauses the motion of theRobotic Arm. It is also used in combination with the PickButton to perform a reset on the roboti

D. SYSTEM REQUIREMENTSPlease refer to the PC system requirements for Duplicator thatwill be used with the unit. NOTE: The ADL-MAX is not Macintosh com